Borg BL5401KSSDDA *Keypad Only* – AS1428.1 Disability Compliant Lever – Satin Stainless
This product is supplied as a keypad unit only. It does not include a latch, inside handle, strike plate, spindle, or fixing screws. It is designed for replacing a worn or damaged outside keypad on an existing BL5401 installation, or for custom installations where the inside hardware and latch are sourced separately.
The Borg BL5401KSSDDA Keypad Only (BL5401KSSDDA) is a replacement outside keypad unit with DDA compliant flat bar lever in satin stainless finish, using the traditional tumbler code system. Code change requires removing the keypad and rearranging the internal tumblers.
If you need on-door code change, see the BL5401KSSDDAECP (ECP keypad only). For a complete lock including inside handle, latch, and all fixings, see the complete lock BL5401SSDDA.
Usually same day if ordered before 11am AEST (excluding weekends and Qld public holidays)
Flat bar lever compliant with BCA AS1428.1-2009. Suitable for disability access doors, accessible toilet facilities, and BCA-compliant applications.
Tumbler-based code system. To change the PIN, the keypad must be removed. Remove the 4 red screws, hold the C tumbler depressed, use tweezers to reposition the tumblers. Over 8,000 combinations; length adjustable 3–7 digits. For on-door code change, see the BL5401KSSDDAECP.
Entirely mechanical. No power source, no wiring, and no battery maintenance.
Key Features
- DDA compliant flat bar lever – AS1428.1-2009.
- Over 8,000 code combinations; length adjustable 3–7 digits with spare tumblers supplied.
- Satin stainless finish.
- 8mm square drive spindle (spindle not included).
- Suitable for replacing worn keypad on existing BL5401 installations.
- Fully mechanical – no batteries, no wiring.
What's in the Box (Keypad Only)
- Borg BL5401 DDA keypad unit with flat bar lever (satin stainless) – keypad only
- 2 × coded tumblers (red – spare)
- 2 × non-coded tumblers (blue – spare)
- Tweezers (for code change)
- Hex wrench (Allen key)
- Handle screw rubber grommet
- Note: Latch, inside handle, spindle, strike plate, and all fixing screws are NOT included – source separately
Compatible Complete Lock Products
Borg BL5401 DDA Series – Product Family
All BL5401 DDA models use the AS1428.1-2009 compliant flat bar DDA lever. All are fully mechanical with no batteries. All full-lock models are fire rated to AS 1905.1-2005 (up to 4 hours depending on doorset).
ECP = Easicode Pro on-door code change. MG Pro = Marine Grade Pro – 316 SS internals – 1,000hr salt spray tested. Keypad-only models require a compatible latch and inside handle sourced separately.
Full Specifications
Frequently Asked Questions
What does this product include?
The BL5401KSSDDA includes the outside keypad unit only, with DDA flat bar lever and spare tumblers. It does not include a latch, inside handle, spindle, strike plate, or fixing screws. These must be sourced separately or reused from the existing installation.
What is the DDA lever and what makes it different from a standard lever?
The BL5401 uses a flat bar lever compliant with BCA AS1428.1-2009 (Design for Access and Mobility). This lever requires significantly less grip force and torque than a round bar lever, making it suitable for users with limited hand strength or dexterity. It is the correct lever type for disability access doors, accessible toilet facilities, and any application where BCA accessibility compliance is required for the locking hardware. Lever compliance relates to the handle design only and does not imply full building access compliance for the installation.
How do I change the PIN code?
The code must be changed with the lock removed from the door. Remove the 4 red screws, carefully lift the cover plate (springs are attached), hold the C tumbler depressed at all times, then use the supplied tweezers to reposition the red (coded) and blue (uncoded) tumblers. All square cut-outs must face outward and coloured marks must face upward. Replace the cover plate and test the new code before reinstalling. Codes are non-sequential — 1234 can be entered in any order.
What is this product compatible with?
This keypad unit is compatible with the BL5401 series lock body configuration. The 8mm square drive spindle suits most leading brands of tubular latch and mortice lock case. Always confirm spindle length and compatibility with your specific lock body before ordering. Refer to the drilling template PDF for correct hole placement.
Can I reverse the handing on site?
Yes. All BL5401 units are factory set for right-hand doors. To change: remove the rubber grommet at the base of the keypad handle, use the included hex wrench to remove the grub screw, rotate the handle 180° and refit. Repeat for the inside handle. Handing is determined from the outside of the door: right hand = hinges on the right; left hand = hinges on the left, regardless of swing direction.
All Borg locks are warranted against mechanical defects in materials and workmanship under normal use and service for a minimum of 12 months from date of sale. The warranty does not cover damage arising from misuse, vandalism, or improper installation. The lock must not be dismantled — doing so will invalidate the warranty.
What's In The Box – Borg BL5401KSSDDA
- Borg BL5401 DDA keypad unit with flat bar lever (satin stainless) – keypad only
- 2 × coded tumblers (red – spare)
- 2 × non-coded tumblers (blue – spare)
- Tweezers (for code change)
- Hex wrench (Allen key)
- Handle screw rubber grommet
- Note: Latch, inside handle, spindle, strike plate, and all fixing screws are NOT included – source separately
Borg BL5401 DDA Series – Real Installations
Borg BL5400 Series – Dimensions
Borg BL5000 Series – Product Brochure
Borg Locks Warranty – Australia
What is Covered
- Mechanical defects in materials and workmanship
- Defects arising under normal use and service conditions
- Repair or replacement of defective units at the discretion of the Australian distributor (LSC)
What is Not Covered
- Damage arising from misuse, vandalism, or abuse
- Damage resulting from improper installation
- Locks that have been dismantled — dismantling invalidates the warranty
- Normal wear and tear
- Cosmetic damage not affecting function
How a Warranty Claim Works
Warranty claims for Borg products in Australia are processed through LSC, the authorised Australian importer and distributor for Borg Locks. If the returned item is found by LSC to be defective, it will be repaired or replaced. Products must be returned to the LSC office with freight charges prepaid within the warranty period. A detailed assessment report is provided to the customer after examination.
Contact Terry’s Locksmiths first — we will assess the issue and manage the warranty process with LSC on your behalf. You do not need to contact LSC or Borg Locks UK directly.
Australian Consumer Law
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The Borg manufacturer warranty above operates alongside — and does not limit — these statutory rights.
It can be overwhelming with all the choices out there. We can help! We are experts with decades of experience in fitting locks of all types, not just Smart Locks. It is a free service we offer, and with just some photos and a few minutes of your time you can get expert advice and product recommendations tailored precisely to suit your needs.
Click on the image below to begin your expert Smart Lock consultation
