Borg BL2606MGPROECP Marine Grade Pro Mechanical Digital Knob Lock - Sliding Door Hook Bolt - Black
At A Glance
At A Glance
DISPATCHSame Day Before 11am
REAL INSTALLS11 Install Photos
PIN CodeThe Borg BL2606MGPROECP (BL2606 MG Pro ECP) is a fully mechanical digital knob lock fitted with a hook bolt specifically designed for sliding doors and pedestrian sliding gates. The hook bolt engages with the door frame strike automatically when the sliding door closes - no manual bolt throw required. To open from outside, the correct PIN code is entered; the inside knob is always free to turn for immediate egress without code entry. The lock is part of the Marine Grade Pro series, finished in MG Pro 2 black marine grade coating and tested to 1,000 hours of continuous salt spray exposure.
The BL2606 MG Pro ECP uses the Easicode Pro (ECP) system, allowing the PIN code to be changed while the lock is fitted to the door or gate using the included code change key - no lock removal required. A code change disabling plug is also included to prevent unauthorised code changes. The lock is entirely mechanical: no batteries, no wiring, no power source of any kind.
For a hinged door requiring a surface-mounted deadbolt in the same marine grade coating, see the BL2605 MG Pro (On The Bench code change). For a satin chrome sliding door hook bolt without marine grade coating, see the BL2506 ECP (Satin Chrome).
Estimated Dispatch
Usually ships same day if ordered before 11am AEST (excludes weekends and Queensland public holidays).
Usually ships same day if ordered before 11am AEST (excludes weekends and Queensland public holidays).
Hook Bolt - Designed Specifically for Sliding Doors and Gates
The BL2606 uses a hook bolt instead of a tubular latch or deadbolt. The hook is shaped to engage correctly with the sliding door frame strike as the door moves into the closed position. It is not suitable for hinged doors. Two strikes are included - a universal sliding door strike and a flat strike - to suit a range of aluminium and timber sliding door frame profiles.
The BL2606 uses a hook bolt instead of a tubular latch or deadbolt. The hook is shaped to engage correctly with the sliding door frame strike as the door moves into the closed position. It is not suitable for hinged doors. Two strikes are included - a universal sliding door strike and a flat strike - to suit a range of aluminium and timber sliding door frame profiles.
Auto-Engages When the Sliding Door Closes - No Manual Locking Required
The hook bolt engages with the strike plate automatically as the sliding door is pulled closed. No code entry or manual bolt throw is needed to secure the door. To open from outside, enter the code; the inside knob is always free to turn for egress at any time.
The hook bolt engages with the strike plate automatically as the sliding door is pulled closed. No code entry or manual bolt throw is needed to secure the door. To open from outside, enter the code; the inside knob is always free to turn for egress at any time.
Marine Grade Pro 2 - Salt Water and UV Resistant Construction
The BL2606 MG Pro ECP uses Borg's MG Pro 2 marine grade external coating, tested to 1,000 continuous hours of salt spray exposure. 316 stainless steel internal components for superior corrosion resistance. The coding chamber is specifically designed to resist salt water ingress. Suitable for pool gates, canal-front and waterfront properties, marina facilities, and coastal environments. For more on MG Pro 2 in practice see MG Pro and ECP Explained - Salt Spray.
The BL2606 MG Pro ECP uses Borg's MG Pro 2 marine grade external coating, tested to 1,000 continuous hours of salt spray exposure. 316 stainless steel internal components for superior corrosion resistance. The coding chamber is specifically designed to resist salt water ingress. Suitable for pool gates, canal-front and waterfront properties, marina facilities, and coastal environments. For more on MG Pro 2 in practice see MG Pro and ECP Explained - Salt Spray.
Easicode Pro - On-Door Code Change
The PIN code can be changed while the lock is fitted using the included code change key. No lock removal, no tools, no special knowledge required. A code change disabling plug is included to prevent unauthorised changes once the code has been set by an administrator. For the full step-by-step procedure see Changing Codes on Mechanical Digital Locks - Borg ECP.
The PIN code can be changed while the lock is fitted using the included code change key. No lock removal, no tools, no special knowledge required. A code change disabling plug is included to prevent unauthorised changes once the code has been set by an administrator. For the full step-by-step procedure see Changing Codes on Mechanical Digital Locks - Borg ECP.
Fully Mechanical - No Batteries Required
Entirely mechanical. No power source, no wiring, and no battery maintenance at any point in the product's lifetime. The lock operates identically on day one and year ten. See What Is a Mechanical Digital Lock? for how the coding chamber works.
Entirely mechanical. No power source, no wiring, and no battery maintenance at any point in the product's lifetime. The lock operates identically on day one and year ten. See What Is a Mechanical Digital Lock? for how the coding chamber works.
Designed for Light to Medium Use
The BL2606 MG Pro ECP is rated for light to medium duty residential and commercial applications - pool gates, courtyard sliding gates, marina access, and shed doors in coastal environments. Cycle tested to 50,000+ operations.
The BL2606 MG Pro ECP is rated for light to medium duty residential and commercial applications - pool gates, courtyard sliding gates, marina access, and shed doors in coastal environments. Cycle tested to 50,000+ operations.
Not Suitable for High Traffic Commercial Use
For high-cycle commercial applications, consider the Lockwood DX Mortice, Borg BL7701 Heavy Duty, or Carbine CDL7100 Heavy Duty. See our guide on heavy duty commercial mechanical digital locks for the full comparison.
For high-cycle commercial applications, consider the Lockwood DX Mortice, Borg BL7701 Heavy Duty, or Carbine CDL7100 Heavy Duty. See our guide on heavy duty commercial mechanical digital locks for the full comparison.
Single PIN Code Only
The BL2606 MG Pro ECP accepts one active PIN code at a time. Multiple codes cannot be stored simultaneously. The code can be changed on the door using Easicode Pro without removing the lock, making periodic code rotation straightforward in shared-access settings.
The BL2606 MG Pro ECP accepts one active PIN code at a time. Multiple codes cannot be stored simultaneously. The code can be changed on the door using Easicode Pro without removing the lock, making periodic code rotation straightforward in shared-access settings.
Key Features
- Hook bolt mechanism designed specifically for sliding doors and pedestrian sliding gates - not suitable for hinged doors.
- Hook bolt auto-engages when the sliding door closes - no manual bolt throw required.
- Easicode Pro (ECP) on-door code change - no lock removal required; code change performed using the included key while the lock is fitted.
- MG Pro 2 marine grade coating - 1,000 hour salt spray tested; 316 stainless steel internal components.
- Coding chamber specifically designed to resist salt water corrosion.
- Fully mechanical - no batteries, no wiring, no power source required.
- Over 4,000 user-defined code combinations.
- 25mm hook bolt projection.
- Inside knob always free to turn - immediate egress without code entry.
- Supplied with two strikes - universal sliding door strike and flat strike - to suit different frame types.
- Code change disabling plug included - prevents unauthorised code changes once set.
- Fully reversible on site for left or right hand sliding door configuration.
- 14-button keypad: 12 coded buttons, 1 clear (C), 1 code change (*).
- Cycle tested to 50,000+ operations.
- Suits doors and gates 35mm to 54mm thick (standard); 85mm XL kit option available separately.
- Browse all Digital Mechanical Locks.
Access Methods
This is a mechanical digital lock: the outside keypad is the only way in. There is no app, fob, card or key override on this model.
What's in the Box
- Borg BL2606 MG Pro ECP digital knob keypad (MG Pro 2 coating, external unit)
- Inside knob assembly
- Hook bolt body
- Universal sliding door strike
- Flat strike plate
- Easicode Pro code change key
- Code change disabling plug (optional use)
- Flat bladed sprung spindle (120mm)
- Fixings and installation hardware
Suitable Uses
- Aluminium and timber pedestrian sliding gates in coastal and marine environments - see Buyer's Guide Ch 16 - Gates.
- Sliding pool gate access in beachside, canal-front, and waterfront properties.
- External sliding doors on sheds, plant rooms, and amenity buildings in coastal zones.
- Sliding gate access in strata, apartment, and managed property settings where regular code changes are required.
- Marine facility and marina sliding gate keyless access control.
- Applications where the door auto-securing on closing is a requirement.
- Browse all Digital Mechanical Locks.
Available Finish Options
Matt Black (MG Pro 2)
(This Product)
STK BL2606MGPROECP
Finish selection does not affect functionality, compliance, or performance.
The satin chrome BL2506SCECP is the same sliding door hook bolt lock with Easicode Pro, in a standard (not marine grade) finish for sheltered or inland locations.
BL2605 vs BL2606 - Which Model Suits Your Application?
BL2605 suits hinged doors where the deadbolt must be manually thrown from inside after closing. BL2606 and BL2506 suit sliding doors and gates - the hook bolt auto-engages on closing. Choose BL2606 for marine/coastal environments (MG Pro 2 black coating, 1,000hr salt spray); choose BL2506 for sheltered or inland locations (satin chrome, rain-resistant standard coating).
Full Specifications
Dimensions
Keypad and inside knob body dimensions - BL2605 / BL2606 series. Door thickness: 35-54mm standard (up to 85mm with XL kit). 25mm hook bolt projection.
Assembly Overview
Assembly and fitting diagram. Shows keypad (outside), hook bolt body (inside), and strike plate positions. Universal and flat strikes both included.
Frequently Asked Questions
Why does this use a hook bolt instead of a standard latch or deadbolt?
Sliding doors and gates move laterally rather than swinging, so a tubular spring latch or rim deadbolt cannot engage correctly with a sliding frame. The hook bolt is shaped to hook into the strike as the door moves into the closed position, providing secure engagement suited to the lateral movement of a sliding door or gate. For a comparison of latch and bolt formats see Latch vs Bolt Mechanical Digital Locks.
Sliding doors and gates move laterally rather than swinging, so a tubular spring latch or rim deadbolt cannot engage correctly with a sliding frame. The hook bolt is shaped to hook into the strike as the door moves into the closed position, providing secure engagement suited to the lateral movement of a sliding door or gate. For a comparison of latch and bolt formats see Latch vs Bolt Mechanical Digital Locks.
Does the door lock automatically when I slide it closed?
Yes. When the sliding door is pulled closed, the hook bolt engages with the strike plate automatically. No code entry or manual bolt throw is needed to secure the door. To open from outside, enter the PIN code. The inside knob is always free to turn so you can open from inside without code entry.
Yes. When the sliding door is pulled closed, the hook bolt engages with the strike plate automatically. No code entry or manual bolt throw is needed to secure the door. To open from outside, enter the PIN code. The inside knob is always free to turn so you can open from inside without code entry.
How do I change the PIN code?
With the door in the open position, enter the current code, insert the included code change key into the hole in the * button and hold it, press C to clear the existing code, enter the new code, release the code change key, then press C to confirm. Test the new code at least five times before closing the door. If a mistake is made during entry, press C to cancel and start again. Full procedure at Changing Codes - ECP Steps.
With the door in the open position, enter the current code, insert the included code change key into the hole in the * button and hold it, press C to clear the existing code, enter the new code, release the code change key, then press C to confirm. Test the new code at least five times before closing the door. If a mistake is made during entry, press C to cancel and start again. Full procedure at Changing Codes - ECP Steps.
Which strike should I use - universal or flat?
Two strikes are included. The universal strike suits most standard aluminium sliding door frame profiles. The flat strike is for timber-framed or flat-profile frame applications. Trial-fit before final fixing and check that the hook bolt enters the strike opening cleanly on every close cycle. A misaligned strike will prevent engagement or cause premature wear. For gate stile sizing guidance see Gate Post - Measure the Stile.
Two strikes are included. The universal strike suits most standard aluminium sliding door frame profiles. The flat strike is for timber-framed or flat-profile frame applications. Trial-fit before final fixing and check that the hook bolt enters the strike opening cleanly on every close cycle. A misaligned strike will prevent engagement or cause premature wear. For gate stile sizing guidance see Gate Post - Measure the Stile.
What is the difference between the BL2606 MG Pro ECP and the BL2605 MG Pro?
The BL2605 MG Pro uses a rim-fixed deadbolt and is designed for hinged doors - the bolt must be manually thrown from inside to lock after the door is closed. The BL2606 MG Pro ECP uses a hook bolt for sliding doors that auto-engages when the door closes. Both share the MG Pro 2 coating and 1,000hr salt spray rating; the BL2605 MG Pro changes its code On The Bench, while the BL2606 adds Easicode Pro on-door code change. If your door or gate slides, the BL2606 is the correct product.
The BL2605 MG Pro uses a rim-fixed deadbolt and is designed for hinged doors - the bolt must be manually thrown from inside to lock after the door is closed. The BL2606 MG Pro ECP uses a hook bolt for sliding doors that auto-engages when the door closes. Both share the MG Pro 2 coating and 1,000hr salt spray rating; the BL2605 MG Pro changes its code On The Bench, while the BL2606 adds Easicode Pro on-door code change. If your door or gate slides, the BL2606 is the correct product.
Additional Information
Strike Selection and Alignment:
The hook bolt must engage cleanly and squarely with the strike on every close cycle. Trial-fit the chosen strike before final fixing and confirm the hook bolt enters the opening without binding. A misaligned strike will cause engagement failure or accelerated wear over time. The universal strike suits the majority of standard aluminium sliding gate and door frame profiles used in Australian residential construction.
The hook bolt must engage cleanly and squarely with the strike on every close cycle. Trial-fit the chosen strike before final fixing and confirm the hook bolt enters the opening without binding. A misaligned strike will cause engagement failure or accelerated wear over time. The universal strike suits the majority of standard aluminium sliding gate and door frame profiles used in Australian residential construction.
Door Thickness - 35 to 54mm Standard, up to 85mm with XL Kit:
The BL2606 MG Pro ECP suits doors and gates from 35mm to 54mm thick with the standard 120mm flat bladed sprung spindle supplied. For gate frames up to 85mm thick, an XL extension kit (Part S227, available separately) extends the spindle to bridge the thicker section. Confirm your gate frame section before ordering.
The BL2606 MG Pro ECP suits doors and gates from 35mm to 54mm thick with the standard 120mm flat bladed sprung spindle supplied. For gate frames up to 85mm thick, an XL extension kit (Part S227, available separately) extends the spindle to bridge the thicker section. Confirm your gate frame section before ordering.
Code Change Disabling Plug:
Once inserted into the code change hole in the * button, the disabling plug prevents the Easicode Pro code change procedure from being initiated on the door. This is useful in managed or shared-access environments where only an administrator should be able to change the code. The plug is removable if code change access needs to be reinstated.
Once inserted into the code change hole in the * button, the disabling plug prevents the Easicode Pro code change procedure from being initiated on the door. This is useful in managed or shared-access environments where only an administrator should be able to change the code. The plug is removable if code change access needs to be reinstated.
Marine Grade Maintenance:
Monthly: wipe the keypad and hook bolt with a light spray of silicon-based lubricant (such as GT85) and remove the excess with a soft cloth. Do not use oil-based lubricants such as WD-40 - they attract dirt and wear down internal parts over time. Annually: remove the lock from the door, spray the inside through the code piece holes on the reverse of the keypad with silicon-based lubricant, spray all fixings, accessories and the hook bolt with silicon-based lubricant, then press each button and rotate the knob several times to confirm smooth operation. Full steps are in the Borg Lock Servicing Guide (PDF).
Monthly: wipe the keypad and hook bolt with a light spray of silicon-based lubricant (such as GT85) and remove the excess with a soft cloth. Do not use oil-based lubricants such as WD-40 - they attract dirt and wear down internal parts over time. Annually: remove the lock from the door, spray the inside through the code piece holes on the reverse of the keypad with silicon-based lubricant, spray all fixings, accessories and the hook bolt with silicon-based lubricant, then press each button and rotate the knob several times to confirm smooth operation. Full steps are in the Borg Lock Servicing Guide (PDF).
Pool Gate Compliance Note:
The lock's job is access control, not the pool barrier's self-latching function. The hook bolt engages on closing, but a pool barrier gate still needs its own compliant self-closing, self-latching hardware (such as a MagnaLatch) doing the barrier job, with this lock providing access control on top of it. Confirm compliance with a licensed pool safety inspector before specifying any lock for a pool gate. See Latch vs Bolt - Pool Gates.
The lock's job is access control, not the pool barrier's self-latching function. The hook bolt engages on closing, but a pool barrier gate still needs its own compliant self-closing, self-latching hardware (such as a MagnaLatch) doing the barrier job, with this lock providing access control on top of it. Confirm compliance with a licensed pool safety inspector before specifying any lock for a pool gate. See Latch vs Bolt - Pool Gates.
Warranty
Borg Locks Warranty - 12 Months (Australia)
All Borg locks are warranted against mechanical defects in materials and workmanship under normal use and service for a minimum of 12 months from date of sale. The warranty does not cover damage arising from misuse, vandalism, or improper installation. The lock must not be dismantled - doing so will invalidate the warranty. Proof of purchase required for all claims.
All Borg locks are warranted against mechanical defects in materials and workmanship under normal use and service for a minimum of 12 months from date of sale. The warranty does not cover damage arising from misuse, vandalism, or improper installation. The lock must not be dismantled - doing so will invalidate the warranty. Proof of purchase required for all claims.
Purchased through Terry's Tradies Pty Ltd or one of its associated trading names? Contact us first - we will manage your warranty claim with the Australian distributor (LSC) on your behalf. This warranty operates alongside your rights under the Australian Consumer Law.
Download PDF Resources
Borg BL2605 ECP MG Series Instructions (PDF)
Installation and maintenance manual written for the BL2005 ECP and BL2605 ECP rim deadbolt models - keypad and deadbolt handing, the Easicode Pro code change, spindle fitting and assembly. Its maintenance page recommends WD-40: for this lock, follow the silicone routine under Additional Information instead.
Installation and maintenance manual written for the BL2005 ECP and BL2605 ECP rim deadbolt models - keypad and deadbolt handing, the Easicode Pro code change, spindle fitting and assembly. Its maintenance page recommends WD-40: for this lock, follow the silicone routine under Additional Information instead.
Borg BL2605 MG Pro ECP Technical Data Sheet (PDF)
One-page data sheet for the BL2605 MG Pro ECP rim deadbolt - the hinged-door model in this 2600 ECP range - with features, specifications and dimensioned keypad drawings.
One-page data sheet for the BL2605 MG Pro ECP rim deadbolt - the hinged-door model in this 2600 ECP range - with features, specifications and dimensioned keypad drawings.
Borg Easicode Pro (ECP) Instructions V4 (PDF)
The on-door Easicode Pro code change procedure and spindle fitting guide, stated by Borg as applicable to all 2000 ECP models.
The on-door Easicode Pro code change procedure and spindle fitting guide, stated by Borg as applicable to all 2000 ECP models.
Borg Lock Servicing Guide (PDF)
Borg's general maintenance guide for pushbutton keypad locks - monthly silicone-based lubricant care and an annual full service. This is the routine to follow for this lock.
Borg's general maintenance guide for pushbutton keypad locks - monthly silicone-based lubricant care and an annual full service. This is the routine to follow for this lock.
Borg BL2606 MG Pro ECP - FAQ, Setup and Owner's Guide
Full detail on the BL2606 MG Pro ECP sliding door hook bolt lock. For context see What Is a Mechanical Digital Lock? and Buyer's Guide Chapter 16 - Mechanical Digital Locks.
The Hook Bolt and How It Works
What is a hook bolt and why does this lock use one?
A hook bolt is a bolt shaped like a fishhook. As the sliding door moves laterally into the closed position, the hook travels through the strike opening and the door's own momentum rotates the hook into engagement. This is the only bolt type that works reliably with a sliding door's lateral movement. A tubular spring latch or rim deadbolt cannot engage correctly with a sliding frame - they require a linear push or manual throw. For the full latch-vs-bolt comparison see Latch vs Bolt Mechanical Digital Locks.
A hook bolt is a bolt shaped like a fishhook. As the sliding door moves laterally into the closed position, the hook travels through the strike opening and the door's own momentum rotates the hook into engagement. This is the only bolt type that works reliably with a sliding door's lateral movement. A tubular spring latch or rim deadbolt cannot engage correctly with a sliding frame - they require a linear push or manual throw. For the full latch-vs-bolt comparison see Latch vs Bolt Mechanical Digital Locks.
Does the door lock automatically every time it closes?
Yes. The hook engages with the strike plate on every close cycle without any code entry or manual action. The door is secured as soon as it reaches the closed position. Opening from outside always requires the PIN code. Opening from inside requires only turning the inside knob - no code, no key.
Yes. The hook engages with the strike plate on every close cycle without any code entry or manual action. The door is secured as soon as it reaches the closed position. Opening from outside always requires the PIN code. Opening from inside requires only turning the inside knob - no code, no key.
Is there a way to leave the door unlocked - like a passage or holdback mode?
No. The hook bolt always engages on closing. There is no holdback or passage mode on the BL2606. If a sliding gate needs to be held open or in a free-passage state for extended periods, a separate door stop or latch-retainer will be needed alongside this lock. See Passage Mode vs Holdback Mode for products that do carry this function.
No. The hook bolt always engages on closing. There is no holdback or passage mode on the BL2606. If a sliding gate needs to be held open or in a free-passage state for extended periods, a separate door stop or latch-retainer will be needed alongside this lock. See Passage Mode vs Holdback Mode for products that do carry this function.
Which strike should I use - the universal or the flat one?
Trial-fit both before committing. The universal strike suits most standard extruded aluminium sliding door and gate frame profiles. The flat strike suits timber frames or frames with a flat, unprofiled facing. The hook bolt must travel cleanly into the strike opening without binding. Too tight and the door will not close properly; too loose and the bolt will rattle. If the gate or door sags over time and the strike misaligns, the lock will appear to fail - this is a frame alignment issue, not a lock fault. For gate-post stile sizing guidance see Gate Post Too Narrow? - Measure the Stile.
Trial-fit both before committing. The universal strike suits most standard extruded aluminium sliding door and gate frame profiles. The flat strike suits timber frames or frames with a flat, unprofiled facing. The hook bolt must travel cleanly into the strike opening without binding. Too tight and the door will not close properly; too loose and the bolt will rattle. If the gate or door sags over time and the strike misaligns, the lock will appear to fail - this is a frame alignment issue, not a lock fault. For gate-post stile sizing guidance see Gate Post Too Narrow? - Measure the Stile.
Is the lock reversible for left and right hand sliding doors?
Yes. Both the keypad handing and the hook bolt handing are reversible on site. The keypad handing is changed by removing two screws from the back cover plate, repositioning the handing pin and disc, and refitting. The hook bolt handing is changed by removing four screws, flipping the deadbolt horizontally, and refitting. These steps follow the BL2605 ECP MG Series Instructions, which were written for the BL2605 ECP rim deadbolt - ask us if your hook bolt differs. The handing diagram distinguishes right-hand hung (door hinged right) from left-hand hung (door hinged left) as viewed from the outside.
Yes. Both the keypad handing and the hook bolt handing are reversible on site. The keypad handing is changed by removing two screws from the back cover plate, repositioning the handing pin and disc, and refitting. The hook bolt handing is changed by removing four screws, flipping the deadbolt horizontally, and refitting. These steps follow the BL2605 ECP MG Series Instructions, which were written for the BL2605 ECP rim deadbolt - ask us if your hook bolt differs. The handing diagram distinguishes right-hand hung (door hinged right) from left-hand hung (door hinged left) as viewed from the outside.
Code Change and PIN Management
How do I change the PIN code on the BL2606?
With the door open: enter the current code, insert the code change key into the * button hole and hold it, press C to clear the existing code, enter the new code, release the code change key, press C to set the new code. Test the new code five times before closing the door. If a mistake is made, press C to cancel and start again from step one. For the full illustrated procedure see Changing Codes - Borg ECP and download the ECP Instructions V4 PDF.
With the door open: enter the current code, insert the code change key into the * button hole and hold it, press C to clear the existing code, enter the new code, release the code change key, press C to set the new code. Test the new code five times before closing the door. If a mistake is made, press C to cancel and start again from step one. For the full illustrated procedure see Changing Codes - Borg ECP and download the ECP Instructions V4 PDF.
Does the code change procedure require the door to be open?
Yes. Borg specifies the code change must be performed with the door in the open position. The code can be changed with the lock fitted to the door or off the door - but not while the door is closed and latched. Always test the new code a minimum of five times with the door open before closing it.
Yes. Borg specifies the code change must be performed with the door in the open position. The code can be changed with the lock fitted to the door or off the door - but not while the door is closed and latched. Always test the new code a minimum of five times with the door open before closing it.
How many code combinations are available?
Over 4,000 user-defined combinations from the 12 coded buttons. The code is set by the user, not pre-programmed at the factory - you choose the combination on installation. This figure is consistent across all 2600 ECP MG series documents.
Over 4,000 user-defined combinations from the 12 coded buttons. The code is set by the user, not pre-programmed at the factory - you choose the combination on installation. This figure is consistent across all 2600 ECP MG series documents.
Can I store multiple PIN codes simultaneously?
No. The BL2606 MG Pro ECP stores one active PIN code at a time. If you need per-user codes or time-limited access management, this lock is not the right product. For a product with back-to-back access in the same marine grade range, see the BL2621 MG Pro ECP (back-to-back, 60mm latch).
No. The BL2606 MG Pro ECP stores one active PIN code at a time. If you need per-user codes or time-limited access management, this lock is not the right product. For a product with back-to-back access in the same marine grade range, see the BL2621 MG Pro ECP (back-to-back, 60mm latch).
What does the code change disabling plug do?
Once inserted into the code change hole in the * button, it physically blocks the code change procedure from being initiated on the door. Only someone who removes the plug first can change the code - useful in managed or shared-access environments where you want administrator-only code control. The plug is removable without tools when access reinstatement is needed.
Once inserted into the code change hole in the * button, it physically blocks the code change procedure from being initiated on the door. Only someone who removes the plug first can change the code - useful in managed or shared-access environments where you want administrator-only code control. The plug is removable without tools when access reinstatement is needed.
Marine Grade and Corrosion Resistance
What does MG Pro 2 actually mean in practice?
MG Pro 2 (Marine Grade Pro 2) is Borg's marine grade external coating designation - a black polymer/epoxy coating applied to the outside of the lock body over the cast housing. It has been tested to 1,000 continuous hours of salt spray exposure. The internal components are 316 stainless steel. The coding chamber is specifically designed to resist salt water ingress. For the full Borg MG Pro vs standard explanation see MG Pro and ECP Explained - MG Pro 2.
MG Pro 2 (Marine Grade Pro 2) is Borg's marine grade external coating designation - a black polymer/epoxy coating applied to the outside of the lock body over the cast housing. It has been tested to 1,000 continuous hours of salt spray exposure. The internal components are 316 stainless steel. The coding chamber is specifically designed to resist salt water ingress. For the full Borg MG Pro vs standard explanation see MG Pro and ECP Explained - MG Pro 2.
Is the corrosion resistance warranted?
Yes. Borg's 12-month warranty covers the lock against mechanical defects under normal use, including corrosion resistance performance. The warranty does not cover damage from improper installation or misuse. Correct maintenance is also important for the warranty to apply - see the maintenance routine in Additional Information.
Yes. Borg's 12-month warranty covers the lock against mechanical defects under normal use, including corrosion resistance performance. The warranty does not cover damage from improper installation or misuse. Correct maintenance is also important for the warranty to apply - see the maintenance routine in Additional Information.
Is this lock suitable for direct salt air and spray environments?
Yes - that is the purpose of the MG Pro 2 designation. The 1,000 hour salt spray test is a laboratory benchmark intended to simulate extended coastal exposure. Borg's standard ECP range (including the BL2506 satin chrome) is rain-resistant but not rated to 1,000 hours salt spray. The MG Pro and ECP blog - Salt Spray section covers the rating comparison in full.
Yes - that is the purpose of the MG Pro 2 designation. The 1,000 hour salt spray test is a laboratory benchmark intended to simulate extended coastal exposure. Borg's standard ECP range (including the BL2506 satin chrome) is rain-resistant but not rated to 1,000 hours salt spray. The MG Pro and ECP blog - Salt Spray section covers the rating comparison in full.
How should I maintain the BL2606 in a coastal environment?
Use the same silicone routine as every Borg keypad lock. Monthly: wipe the keypad and hook bolt with a light spray of silicon-based lubricant (such as GT85) and remove the excess with a soft cloth. Do not use oil-based lubricants such as WD-40 - they attract dirt and wear down internal parts over time. Annually: remove the lock from the door, spray the inside through the code piece holes on the reverse of the keypad with silicon-based lubricant, spray all fixings, accessories and the hook bolt with silicon-based lubricant, then press each button and rotate the knob several times to confirm smooth operation. The BL2605 ECP MG Series Instructions suggest WD-40 - do not use it on this lock; follow the Borg Lock Servicing Guide (PDF).
Use the same silicone routine as every Borg keypad lock. Monthly: wipe the keypad and hook bolt with a light spray of silicon-based lubricant (such as GT85) and remove the excess with a soft cloth. Do not use oil-based lubricants such as WD-40 - they attract dirt and wear down internal parts over time. Annually: remove the lock from the door, spray the inside through the code piece holes on the reverse of the keypad with silicon-based lubricant, spray all fixings, accessories and the hook bolt with silicon-based lubricant, then press each button and rotate the knob several times to confirm smooth operation. The BL2605 ECP MG Series Instructions suggest WD-40 - do not use it on this lock; follow the Borg Lock Servicing Guide (PDF).
Installation, Door and Gate Suitability
What door or gate thicknesses does this lock suit?
35mm to 54mm with the standard 120mm flat bladed sprung spindle supplied. Gates up to 85mm thick can be accommodated with the XL extension kit (Part S227, ordered separately). Most standard Australian aluminium sliding gate sections fall within the 35-54mm standard range. Measure the gate frame section - not the gate leaf - before ordering.
35mm to 54mm with the standard 120mm flat bladed sprung spindle supplied. Gates up to 85mm thick can be accommodated with the XL extension kit (Part S227, ordered separately). Most standard Australian aluminium sliding gate sections fall within the 35-54mm standard range. Measure the gate frame section - not the gate leaf - before ordering.
Can I fit this to a pool gate?
The lock's job is access control, not the pool barrier's self-latching function. The hook bolt engages on closing, but a pool barrier gate still needs its own compliant self-closing, self-latching hardware (such as a MagnaLatch) doing the barrier job, with this lock providing access control on top of it. Confirm compliance with a licensed pool safety inspector before specifying any lock for a pool gate. See Latch vs Bolt - Pool Gates.
The lock's job is access control, not the pool barrier's self-latching function. The hook bolt engages on closing, but a pool barrier gate still needs its own compliant self-closing, self-latching hardware (such as a MagnaLatch) doing the barrier job, with this lock providing access control on top of it. Confirm compliance with a licensed pool safety inspector before specifying any lock for a pool gate. See Latch vs Bolt - Pool Gates.
Can this be fitted to a hinged gate or door?
No. The hook bolt is designed for lateral sliding movement and will not function correctly on a hinged door or gate. For a hinged door in a coastal environment, see the BL2605 MG Pro (rim-fixed deadbolt, hinged doors and gates, On The Bench code change). For a back-to-back gate lock in marine grade, see the BL3430 MG Pro ECP (forend-fixed, hinged gate, dual keypads).
No. The hook bolt is designed for lateral sliding movement and will not function correctly on a hinged door or gate. For a hinged door in a coastal environment, see the BL2605 MG Pro (rim-fixed deadbolt, hinged doors and gates, On The Bench code change). For a back-to-back gate lock in marine grade, see the BL3430 MG Pro ECP (forend-fixed, hinged gate, dual keypads).
Does the spindle need to be cut to length during installation?
Only the inside-handle side of the spindle may be cut if the spindle is too long for the door thickness. The keypad side must never be cut - the full bladed length is needed to reach the back of the cylinder and ensure correct operation. This is stated explicitly in the ECP Instructions V4 and applies to both key override and non-key-override models. The spring around one side of the spindle (on key override models) must be positioned between the keypad and the side of the latch.
Only the inside-handle side of the spindle may be cut if the spindle is too long for the door thickness. The keypad side must never be cut - the full bladed length is needed to reach the back of the cylinder and ensure correct operation. This is stated explicitly in the ECP Instructions V4 and applies to both key override and non-key-override models. The spring around one side of the spindle (on key override models) must be positioned between the keypad and the side of the latch.
Mechanical Digital Identity - No Batteries, No App
Why would I choose a fully mechanical lock over an electronic smart lock?
The BL2606 requires no power at all. There are no batteries to go flat, no firmware to update, no app to configure, no connectivity to lose, and no vulnerability to cyber attack. On a pool gate or marina sliding gate - where the lock is exposed to salt water, UV, and temperature extremes - the absence of electronics is a significant reliability advantage. Battery-powered smart locks in coastal environments have a poor track record of premature failure. See What Is a Mechanical Digital Lock - Why Choose One? and The Realities of Electronic Door Locks.
The BL2606 requires no power at all. There are no batteries to go flat, no firmware to update, no app to configure, no connectivity to lose, and no vulnerability to cyber attack. On a pool gate or marina sliding gate - where the lock is exposed to salt water, UV, and temperature extremes - the absence of electronics is a significant reliability advantage. Battery-powered smart locks in coastal environments have a poor track record of premature failure. See What Is a Mechanical Digital Lock - Why Choose One? and The Realities of Electronic Door Locks.
What are the limitations I should know about before buying?
Single PIN code only - no per-user codes or access schedules. No key override - if you need a mechanical key backup, look at the BL2701MGPRO (Marine Grade Pro, hinged doors) or the Lockwood DX range. No audit trail, no remote management, no notifications. The hook bolt suits sliding gates only - not hinged doors. Like all mechanical digital locks, there is no lockout function or user-level management beyond rotating the single code. See Mechanical Digital Locks - Limitations.
Single PIN code only - no per-user codes or access schedules. No key override - if you need a mechanical key backup, look at the BL2701MGPRO (Marine Grade Pro, hinged doors) or the Lockwood DX range. No audit trail, no remote management, no notifications. The hook bolt suits sliding gates only - not hinged doors. Like all mechanical digital locks, there is no lockout function or user-level management beyond rotating the single code. See Mechanical Digital Locks - Limitations.
Related Products, Guides and Chapters
- Borg BL2506SCECP (satin chrome sliding door hook bolt, Easicode Pro)
- Borg BL2605 MG Pro (hinged door rim deadbolt, On The Bench code change)
- Borg BL2601 MG Pro ECP (60mm latch)
- Borg BL2621 MG Pro ECP (back-to-back, 60mm latch)
- Borg BL2615 MG Pro ECP (horizontal rim deadbolt gate lock, non-handed)
- Borg BL3430 MG Pro ECP (hinged gate, dual keypads)
- Borg BL3400 MG Pro ECP (hinged gate lock, single keypad)
- Borg BL2701MGPRO (Marine Grade Pro with key override)
- Lockwood 3572DX (heavy duty alternative)
- Borg BL7701 (heavy duty alternative)
- Carbine CDL7100SC-HD (heavy duty alternative)
- MG Pro and ECP Explained (blog)
- Latch vs Bolt Mechanical Digital Locks (blog)
- Lockwood vs Borg vs Carbine - Borg MG Pro (blog)
- Why Double-Sided Locks for Gates (blog)
- Gate Post Too Narrow for a 60mm Latch? (blog)
- Why Magnetic Gate Latches Can Be Problematic (blog)
- Changing Codes - Borg ECP (blog)
- Why Our Mech-Digi Range Beats Imitations (blog)
- Buyer's Guide Ch 16 - Gates
- Buyer's Guide Ch 16 - Borg Naming Decoded
- Buyer's Guide Ch 16 - Three Brands Compared
What's In The Box - Borg BL2606 MG Pro ECP
- Borg BL2606 MG Pro ECP digital knob keypad (MG Pro 2 marine grade coating, external unit)
- Inside knob assembly
- Hook bolt body
- Universal sliding door strike
- Flat strike plate
- Easicode Pro code change key
- Code change disabling plug (optional use)
- Flat bladed sprung spindle (120mm)
- Fixings and installation hardware
Installation documents are in the PDF Files tab - the BL2605 ECP MG Series Instructions (written for the BL2605 ECP rim deadbolt) and the Easicode Pro Instructions V4.
Borg BL2605 / BL2606 MG Pro - Real Installations
Borg BL2606 MG Pro ECP - Dimensions
Keypad and inside knob body dimensions - BL2605 / BL2606 series. Door thickness: 35-54mm standard (up to 85mm with XL kit Part S227). 25mm hook bolt projection.
Assembly Overview
Assembly and fitting diagram. Shows keypad (outside), hook bolt body (inside), and strike plate positions. Universal and flat strikes both included.
Borg BL2605 ECP MG Series - Product Brochure
Borg BL2605 MG Pro ECP data sheet page - written for the BL2605 ECP rim deadbolt, the hinged-door model in this 2600 ECP range - with features, specifications and dimensional data.
PDF Files - BL2606MGPROECP
Borg BL2605 ECP MG Series Instructions (PDF)
Installation and maintenance manual written for the BL2005 ECP and BL2605 ECP rim deadbolt models - keypad and deadbolt handing, the Easicode Pro code change, spindle fitting and assembly. Its maintenance page recommends WD-40: for this lock, follow the silicone routine under Additional Information instead.
Installation and maintenance manual written for the BL2005 ECP and BL2605 ECP rim deadbolt models - keypad and deadbolt handing, the Easicode Pro code change, spindle fitting and assembly. Its maintenance page recommends WD-40: for this lock, follow the silicone routine under Additional Information instead.
Borg BL2605 MG Pro ECP Technical Data Sheet (PDF)
One-page data sheet for the BL2605 MG Pro ECP rim deadbolt - the hinged-door model in this 2600 ECP range - with features, specifications and dimensioned keypad drawings.
One-page data sheet for the BL2605 MG Pro ECP rim deadbolt - the hinged-door model in this 2600 ECP range - with features, specifications and dimensioned keypad drawings.
Borg Easicode Pro (ECP) Instructions V4 (PDF)
The on-door Easicode Pro code change procedure and spindle fitting guide, stated by Borg as applicable to all 2000 ECP models.
The on-door Easicode Pro code change procedure and spindle fitting guide, stated by Borg as applicable to all 2000 ECP models.
Borg Lock Servicing Guide (PDF)
Borg's general maintenance guide for pushbutton keypad locks - monthly silicone-based lubricant care and an annual full service. This is the routine to follow for this lock.
Borg's general maintenance guide for pushbutton keypad locks - monthly silicone-based lubricant care and an annual full service. This is the routine to follow for this lock.
Borg Locks Warranty
Borg products sold in Australia are covered against mechanical defects in materials and workmanship under normal use and service. Warranty claims are handled by Terry's Tradies Pty Ltd and its associated websites, trading names, and subsidiaries.
Warranty Summary
What the Warranty Covers
- Mechanical defects in materials and workmanship
- Defects arising under normal use and service conditions
- Repair or replacement of defective units at the discretion of the Australian distributor (LSC)
What the Warranty Does Not Cover
- Damage arising from misuse, vandalism, or abuse
- Damage resulting from improper installation
- Locks that have been dismantled - dismantling invalidates the warranty
- Normal wear and tear
- Cosmetic damage not affecting function
How to Make a Claim
For full returns and warranty claim procedures, visit our Returns & Warranty page - this is kept up to date and is the authoritative reference for current claim steps.
- Contact Terry's Tradies Pty Ltd first if you purchased through us or one of its associated trading names - we will assess the issue and manage the warranty process with LSC on your behalf. You do not need to contact LSC or Borg Locks UK directly.
- Have your proof of purchase ready (receipt or order confirmation).
- Warranty claims for Borg products in Australia are processed through LSC, the authorised Australian importer and distributor. Where an item is returned to LSC, freight charges must be prepaid and the item returned within the warranty period.
- If LSC finds the returned item to be defective, it will be repaired or replaced, and a detailed assessment report is provided to the customer after examination.
Australian Consumer Law
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The Borg manufacturer warranty above operates alongside - and does not limit - these statutory rights.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The Borg manufacturer warranty above operates alongside - and does not limit - these statutory rights.
Confused? Overwhelmed? We get it.
Choosing the right smart lock can be genuinely tricky - door types, backsets, app platforms, compatibility with your existing hardware... there is a lot to consider. We have decades of experience fitting locks of all types, including smart locks, and we are happy to help.
Our expert recommendation service is free. Upload a few photos of your door and describe what you need, and one of our qualified locksmiths will give you a personalised recommendation.
Get Your Free Recommendation →How it works - three easy steps:
1. Upload photos
A few clear shots of your door, lock and frame - inside and out.
2. We assess
Our locksmith reviews your setup and requirements - door type, weather exposure, how you want to use it.
3. You get a recommendation
A personalised recommendation tailored to your door, budget and needs. No pressure, no upsell.
Also useful while you are deciding:
